The Android 4.2.2 Jelly Bean firmware with firmware build number I9295VJUBMK4 has been resealed for Samsung Galaxy S4 Active I9295. Samsung Galaxy S4 Active I9295 users can now update their devices with Android 4.2.2 Jelly Bean official firmware. It is available as an OTA update as well as through Samsung KIES. If you want to install this firmware manually follow this article steps.
Firmware Details:
Version: Android 4.4.2
Changelist: 2045428
Build date: Tue, 19 Nov 2013
Product Code: TPA
PDA: I9295VJUBMK4
CSC: I9295UUBBMK1
MODEM: I9295VJUBMK4
Country: Panama
Disclaimer:
We and the developer of this update procedures shall not be held responsible if any undesirable outcomes may happen to your device. use of this update guide is solely at your own risk!
Read the warnings below and decide whether you want to update your device or not.
– Before updating your phone backup entire data otherwise you will lose it. Update the phone at your own risk and we can’t be held responsible if something goes wrong or if the device gets bricked.
– Use Go Backup Pro or Super Backup to backup all the android apps, contact, sms and all data stored on your phone. If your device is rooted you can use Titanium Backup to backup all your data.
– After installing the Android update outside the country may create problems with phone’s network and the phone’s 2G or 3G network may not even work thereby disabling the phone to make any voice call.
– If you are going to update your device and your device is already rooted, you may lose you rooting but can root it again.
Download Required Files:
– Samsung USB Driver: Link 1 | Link 2 (Direct)
– Odin3 v3.07: Link 1 | Link 2 | Link 3 | Link 4
– Android 4.2.2 VJUBMK4 Jelly Bean Firmware for Galaxy S4 Active I9295 (I9295VJUBMK4_I9295UUBBMK1_TPA.zip)
Pre-Requisites:
1. Install USB Drivers for Samsung Galaxy S4 on your computer.
2. Check your device model Settings -> About device -> Model number.
3. Enable USB Debugging Mode on the phone by navigating to Settings -> Developer Options.
4. Ensure the battery of the phone is charged more than 80 percent.
5. Make a backup of all your important data before following the guide.
6. The Galaxy S4 should be factory unlocked and not locked to any particular carrier.
7. Verify the model number of the Galaxy S4 by navigating to Settings -> About Phone.
Steps to Update Galaxy S4 Active I9295 with Android 4.2.2 VJUBMK4 Jelly Bean Firmware:
Step 1: Extract Firmware zip file and you will get a .tar.md5 file.
Step 2: Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
Step 2: Start your phone in Download mode by pressing and holding “Volume Down”+”Home”+”Power” buttons together until a “Warning!” message appears on screen. Now press the “Volume Up” button to enter Download Mode.
Step 5: Open Odin3 v3.07 on the computer.
Step 6: Connect the Galaxy S4 Active to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the device. When the device is connected successfully, the ID: COM box will turn to light blue with the COM port number. Additionally, the successful connected will be indicated by a message saying Added.
Note: If the Added message does not appear, then try re-install USB drivers or changing the port on the computer.
Step 7: In Odin, Click the AP button and select the “I9295VJUBMK4_I9295UUBBMK1_TPA.tar.md5” file.
Step 8: Verify that “Auto Reboot” and “F. Reset” Time checkboxes are selected in Odin. Also, ensure the “Re-Partition” option is NOT selected.
Step 9: Now hit the Start button to begin the installation process, Sit back and wait a few minutes.
Step 10: Once the installation process completes, your phone will restart and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can now unplug the USB cable to disconnect your device from the computer.
Samsung Galaxy S4 Active I9295 should be now updated with Android 4.2.2 VJUBMK4 Jelly Bean firmware. Head over to Settings -> About Phone to verify the software version running on the device.
If you encounter any issues like FC or Bootloop with the firmware then follow these steps:
Step 1: Restart your phone into recovery mode by pressing “Volume Up”+”Home”+”Power”
Step 2: Choose to wipe/factory reset. (THIS WILL ERASE ALL OF YOUR DATA INCLUDING YOUR INTERNAL SD CARD!)
Step 3: Then choose reboot.
